If you have no hot water, lukewarm water, a leak or a banging tank, a plumber who works on water heaters is the right first call. The plumber checks power or gas, tests the thermostat, element or igniter, looks at the valves and the tank, and gives you a repair price or a replace-instead recommendation. Many repairs finish in one visit.
This page explains who to call, what common repairs cost in the Sacramento area, which checks are safe to do yourself, and when a repair stops making sense. If the tank is leaking from the body, read why a water heater leaks first. If it is an emergency, see emergency water heater repair.
Who do I call if my hot water heater isn't working?
Call a plumber who lists water heater repair, not a general handyman. If the heater runs on gas, the person must be able to work on gas piping and venting. If it is electric, a plumber can handle the tank and the connections, and an electrician is called for problems in the wiring or the breaker panel.
A gas smell changes the order of calls, and the Sactown Plumbing Guide has other help if you need it. Leave the house, then call 911 and the gas utility from outside. Do not flip switches or try to relight anything. For everything else, start by getting two or three quotes from local specialists so you can compare the diagnosis as well as the price. Our quote page is one place to start.
Before you call, note these facts. They save time and often change the price:
- Gas or electric, and the rough age from the label on the tank.
- Tank size in gallons and whether it sits in a garage, closet or utility room.
- What you see: no hot water, not enough, water too hot, noise, a drip, a smell.
- Whether you have already checked the breaker or the pilot.
Do plumbers handle water heaters?
Yes. Water heaters are core plumbing work. A plumber connects the cold and hot water lines, the temperature and pressure relief valve and its discharge pipe, the drain valve, and on gas models the gas connection and vent. Plumbers also handle the expansion tank where one is used.
In California, a contractor needs a license when a job is $1,000 or more in labor and materials, and plumbing work falls under the C-36 plumbing classification. A small repair can come in under that line, but a replacement usually does not. You can check any contractor's license on the California Contractors State License Board (CSLB) website before you agree to a price. Ask for the license number, then look it up yourself.
What does water heater repair cost in Sacramento?
Fixr's water heater repair guide (updated August 2025) says water heater repair costs $150 to $750, with an average of $450, and the part that fails decides where you land. A new thermostat, heating element, igniter or thermocouple is usually the low end. A failed tank or work that needs permits and code upgrades pushes the price up, and a tank replacement runs $1,200 to $2,300 per This Old House. Sacramento prices vary, and the plumber quotes the real figure after looking at your unit.
| Repair | Typical range | What drives the price |
|---|---|---|
| Thermostat or heating element (electric) | $100 to $250 for a thermostat, $200 to $750 for a heating element | Number of elements, access, part brand |
| Igniter, thermocouple or pilot assembly (gas) | $150 to $325 for a thermocouple, $75 to $175 for pilot light repair | Model, part availability, whether the burner needs cleaning |
| Temperature and pressure relief valve | $100 to $250 | Discharge pipe condition, whether the water is shut off easily |
| Drain valve or anode rod | $100 to $200 for a drain valve, $125 to $300 for an anode rod | Corroded fittings, tight clearance |
| Gas control valve | $150 to $300 | Model-specific part, labor to drain and refill |
| Expansion tank | $150 to $400 (Fixr, 40-gallon guide) | Tank size, whether a pressure-reducing valve is also needed |
There is usually a diagnostic or service-call fee, and it is often credited to the repair if you go ahead. Ask when you book. Evening, weekend and holiday visits typically cost more, so a repair that can wait until a weekday morning is often cheaper.
Should you repair it or replace it?
Repair when the part is cheap and the tank is under about 8 to 10 years old and not leaking from the shell. Replace when the tank body leaks, when the repair costs more than roughly half a new heater, or when the unit is at or past the usual 10 to 15 year life. Tank life depends on water quality and maintenance.
Two quick rules help. First, a leak from a fitting or valve can be repaired, but water running from the tank seam or bottom means the steel has failed. Second, if the heater is old and also needs a costly part, the same money goes further toward a new unit with a fresh warranty. See how long a water heater lasts and the water heater replacement cost before you decide. If you are leaning toward replacing, choosing a plumber for water heater replacement covers what the job involves.
A note on size when you replace: a 40 gallon tank is often enough for a household of two or three, and many households with three or four people and two bathrooms choose 50 gallons. Hot-water use is what matters, so the plumber should ask about showers, a soaking tub, the dishwasher and laundry habits. Our guide to the 40 gallon gas water heater covers that size in detail.
How do you reset a hot water heater?
Most electric tank heaters have a red reset button on the upper thermostat, behind a metal access panel. Turn the power off at the breaker first, remove the panel and insulation, press the button once, and restore power. If it trips again, stop. A repeat trip means a failed thermostat, element or wiring problem that needs a plumber or electrician.
Gas water heaters generally do not have a reset button in the same way. They have a gas control with a pilot or an electronic igniter, and the lighting instructions are printed on the tank label. If the pilot will not stay lit, the cause is often a worn thermocouple, a dirty pilot tube or a faulty gas control, and the repair is a job for a plumber. Never bypass a safety device. For more step-by-step troubleshooting, see what to do when a hot water heater is not working or no hot water.
Why is my water heater making noise or dripping?
Popping, rumbling or crackling usually means sediment on the bottom of the tank. The water trapped under the sediment boils and bubbles up through it. Flushing the tank often quiets it, and the steps are in how to flush a water heater. Ticking from pipes after a heat cycle is usually just expansion and is harmless.
A drip needs a closer look. Water from the discharge pipe at the relief valve can mean pressure is too high, or the valve has worn out. Our page on relief valve replacement explains the difference. A slow drip at a pipe connection may be a simple fitting repair. Water pooling under the tank or running from the shell is a replacement conversation. Turn off the power or gas, close the cold water supply to the heater, and call a plumber the same day.
Do water heater repairs need a permit in Sacramento?
Replacing a water heater needs a plumbing permit in the City of Sacramento, and the city lists building permit and related fees for residential water heater new or replacement work. For a small repair such as a thermostat or element, ask the plumber or the building office whether a permit applies. Rules differ between the city and the county, so ask the plumber which applies to your address and who pulls the permit.
California also requires water heaters to be braced against earthquakes under Health and Safety Code section 19211, which refers to the California Plumbing Code. Straps are usually part of any replacement. Ask the plumber to confirm the strapping, the relief valve discharge pipe and the venting are done to code, and to show you the inspection sign-off if one is required.
What about specific brands and parts?
The repair process is much the same across brands, but part availability differs. A. O. Smith, Rheem, Bradford White, State and Whirlpool-branded tanks are widely sold, and plumbers stock common parts for them. Tankless units from Rinnai, Noritz, Navien and others use their own error codes and parts. Commercial-style gas units from Lochinvar and similar makers are less common in homes.
If your heater is a particular make, ask whether the plumber services that brand and can order parts quickly. Our page on A. O. Smith water heater repair covers one of the most common makes. If the unit is still under warranty, check the label for the model and serial number first, because a warranty repair may have to go through the manufacturer's process.
Which water heaters use less energy, electric or gas?
Electric tank heaters convert nearly all their electricity into heat but electricity usually costs more per unit of heat than natural gas. Gas heaters cost less to run in most homes, but need venting and a gas line. Heat pump models use far less electricity than standard electric tanks. The best fit depends on what your house already has. See electric vs gas water heaters.
Instant, or tankless, electric heaters often draw very large amounts of power when running, so they can need a panel upgrade, but they only use energy while hot water is flowing. A plumber or electrician can tell you what your panel can carry.
Questions people ask
Where is the reset button on my heater?
On an electric tank heater, the reset button is a small red button on the upper thermostat behind the top access panel. Switch off the breaker before opening the panel. Gas tank heaters usually do not have a household reset button. Tankless units often show an error code and can sometimes be reset by cycling power, so check the manual.
What size hot water heater do I need?
Size by the first-hour rating on the yellow EnergyGuide label, which is how much hot water the unit delivers in the first hour of heavy use, and match it to your busiest hour. As a rough guide, a 40 gallon tank suits one to three people, 50 gallons suits three to four, and larger families often need 50 to 75 gallons or a high-output unit.
What is the first thing to check when there is no hot water?
For an electric heater, check the breaker and the red reset button, with the power off before you open the panel. For a gas heater, check that the gas valve is open and whether the pilot or igniter is working, following the label. Also confirm the cold water supply valve is open. If you smell gas, leave and call 911.
How do I reset my water heater?
For an electric tank, turn the breaker off, remove the upper access panel, press the red reset button, replace the cover and turn the breaker back on. Wait an hour or so for the water to heat. If it trips again, there is a fault that needs a plumber or electrician. Gas heaters are relit using the label instructions.
What are the top 5 brands of water heaters?
There is no official ranking. The brands you will see most often in the Sacramento area are A. O. Smith, Rheem, Bradford White, State and, for tankless, Rinnai and Navien. Rather than choosing by name, compare the warranty length, the first-hour rating, the energy factor and whether a local plumber can get parts quickly.
Read on
- 40 gallon gas water heater
Is a 40 gallon gas water heater right for your Sacramento home?
- A. O. Smith heater repair
A. O. Smith water heater repair in Sacramento: common faults, what the data plate and manual tell you, safe checks, warranty tips and…
- Emergency water heater repair
Water heater leaking, no hot water or a gas smell?
- Heater not working
Hot water heater not working? Match your symptom to the likely fault, see which fixes are safe to try and what repairs cost for Sacramento…
- Water heater lifespan
How long does a water heater last? Typical lifespans for gas, electric, tankless and heat pump units, signs yours is failing, and how to…
- Flush a water heater
How to flush a water heater tank step by step, how often to do it, how long it takes, what it costs a plumber, and when to leave it alone.
- No hot water checks
No hot water at home? Check the breaker, pilot, thermostat and valves in order, learn what each cause costs to fix, and when to call a…
- Water heater replacement help
Plumber for water heater replacement: what the job involves in Sacramento, what it costs, permit and bracing rules, and what to ask before…
- Relief valve replacement
Water heater pressure relief valve replacement in Sacramento: why the valve drips, how it is replaced, discharge pipe rules and a sourced…
- Electric vs gas heaters
Electric or gas water heater for a Sacramento home?
- Water heater leaking
Water heater leaking in Sacramento? Find where the water comes from, which leaks are minor, which mean a new tank, and what a local…
- Water heater replacement cost
What a water heater replacement costs in Sacramento, from a basic 40-gallon tank to a full upgrade, plus what moves the price and how to…
Sources used
Last changed